(RISOLTO) smontare fs con usb 3.0

[fabio.o]

Ciao a tutti
Purtroppo non so per quale motivo con mint la porta USB 3.0 mi da qualche problema...
Ogni volta che provo a smontare un qualsiasi cosa, che sia penna USB o hdd esterno , mi si comporta in maniera strana, ovvero:
Quando provo a smontare per estrarre la penna USB subito la smonta, ma senza neanche dami il tempo di staccarla che subito la rimonta in automatico....
Per le pennette poco male, ma l hdd esterno se lo stacco che ancora gira potrebbe subire dei danni... Con l USB normale infatti quando premo smonta si spegne tutto e smette di fare il tipico rumore fruscio solito degli hard disk... Invece quando collegato alla porta 3.0 in pratica non si spegne mai e anzi si rimonta in automatico...
Come risolvere?
Grazie a tutti

[andrea111]

Proviamo a guardare cosa dicono i log.
Apri registro di Sistema, posizionati in fondo alle ultime righe poi smonta l'USB --> appariranno delle righe relative all'operazione in atto, poi immediatamente dopo appariranno altre righe relative all'auto-rimontaggio successivo.

Posta tutte le righe che appaiono dallo smontaggio in poi, vediamo se si capisce qualcosa.

[fabio.o]

Codice Seleziona Espandi

Jul 4 08:54:18 Fabio-VGN4290S kernel: [ 75.829209] usb 2-1: new SuperSpeed USB device number 2 using xhci_hcd
Jul 4 08:54:18 Fabio-VGN4290S kernel: [ 75.856712] usb 2-1: New USB device found, idVendor=0951, idProduct=1666
Jul 4 08:54:18 Fabio-VGN4290S kernel: [ 75.856722] usb 2-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
Jul 4 08:54:18 Fabio-VGN4290S kernel: [ 75.856727] usb 2-1: Product: DataTraveler 3.0
Jul 4 08:54:18 Fabio-VGN4290S kernel: [ 75.856731] usb 2-1: Manufacturer: Kingston
Jul 4 08:54:18 Fabio-VGN4290S kernel: [ 75.856735] usb 2-1: SerialNumber: 5404B1090100E6
Jul 4 08:54:18 Fabio-VGN4290S mtp-probe: checking bus 2, device 2: "/sys/devices/pci0000:00/0000:00:14.0/usb2/2-1"
Jul 4 08:54:18 Fabio-VGN4290S mtp-probe: bus: 2, device: 2 was not an MTP device
Jul 4 08:54:18 Fabio-VGN4290S kernel: [ 76.031685] usb-storage 2-1:1.0: USB Mass Storage device detected
Jul 4 08:54:18 Fabio-VGN4290S kernel: [ 76.034655] scsi host2: usb-storage 2-1:1.0
Jul 4 08:54:18 Fabio-VGN4290S kernel: [ 76.035341] usbcore: registered new interface driver usb-storage
Jul 4 08:54:18 Fabio-VGN4290S kernel: [ 76.080820] usbcore: registered new interface driver uas
Jul 4 08:54:19 Fabio-VGN4290S kernel: [ 77.035290] scsi 2:0:0:0: Direct-Access Kingston DataTraveler 3.0 PQ: 0 ANSI: 6
Jul 4 08:54:19 Fabio-VGN4290S kernel: [ 77.036385] sd 2:0:0:0: Attached scsi generic sg2 type 0
Jul 4 08:54:19 Fabio-VGN4290S kernel: [ 77.039785] sd 2:0:0:0: [sdb] 30218842 512-byte logical blocks: (15.5 GB/14.4 GiB)
Jul 4 08:54:19 Fabio-VGN4290S kernel: [ 77.040959] sd 2:0:0:0: [sdb] Write Protect is off
Jul 4 08:54:19 Fabio-VGN4290S kernel: [ 77.040967] sd 2:0:0:0: [sdb] Mode Sense: 4f 00 00 00
Jul 4 08:54:19 Fabio-VGN4290S kernel: [ 77.041202] sd 2:0:0:0: [sdb] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
Jul 4 08:54:19 Fabio-VGN4290S kernel: [ 77.054049] sdb: sdb1
Jul 4 08:54:19 Fabio-VGN4290S kernel: [ 77.055136] sd 2:0:0:0: [sdb] Attached SCSI removable disk
Jul 4 08:54:25 Fabio-VGN4290S udisksd[1775]: Mounted /dev/sdb1 at / media/fabio/ USB on behalf of uid 1000
Jul 4 08:54:28 Fabio-VGN4290S systemd[1]: Starting Stop ureadahead data collection...
Jul 4 08:54:28 Fabio-VGN4290S systemd[1]: Started Stop ureadahead data collection.
Jul 4 08:54:28 Fabio-VGN4290S systemd[1]: Stopped Read required files in advance.
Jul 4 08:54:36 Fabio-VGN4290S ntpd[1115]: error resolving pool 1.ubuntu.pool.ntp.org: Temporary failure in name resolution (-3)
Jul 4 08:54:36 Fabio-VGN4290S ntpd[1115]: error resolving pool 0.ubuntu.pool.ntp.org: Temporary failure in name resolution (-3)
Jul 4 08:54:37 Fabio-VGN4290S ntpd[1115]: error resolving pool 2.ubuntu.pool.ntp.org: Temporary failure in name resolution (-3)
Jul 4 08:54:39 Fabio-VGN4290S ntpd[1115]: error resolving pool 3.ubuntu.pool.ntp.org: Temporary failure in name resolution (-3)
Jul 4 08:54:40 Fabio-VGN4290S ntpd[1115]: error resolving pool ntp.ubuntu.com: Temporary failure in name resolution (-3)
Jul 4 08:54:47 Fabio-VGN4290S udisksd[1775]: Cleaning up mount point /media/fabio/ USB (device 8:17 is not mounted)
Jul 4 08:54:47 Fabio-VGN4290S udisksd[1775]: Unmounted /dev/sdb1 on behalf of uid 1000
Jul 4 08:54:47 Fabio-VGN4290S udisksd[1775]: Ignoring SCSI command SYNCHRONIZE CACHE failure (Non-GOOD SCSI status from SGIO v3 ioctl: status=2 host_status=0 driver_status=8) on /dev/sdb
Jul 4 08:54:47 Fabio-VGN4290S udisksd[1775]: Successfully sent SCSI command START STOP UNIT to /dev/sdb
Jul 4 08:54:47 Fabio-VGN4290S udisksd[1775]: Powered off /dev/sdb - successfully wrote to sysfs path /sys/devices/pci0000:00/0000:00:14.0/usb2/2-1/remove
Jul 4 08:54:47 Fabio-VGN4290S kernel: [ 104.467176] usb 2-1: USB disconnect, device number 2
Jul 4 08:54:47 Fabio-VGN4290S kernel: [ 105.231833] usb 2-1: new SuperSpeed USB device number 3 using xhci_hcd
Jul 4 08:54:47 Fabio-VGN4290S kernel: [ 105.259445] usb 2-1: New USB device found, idVendor=0951, idProduct=1666
Jul 4 08:54:47 Fabio-VGN4290S kernel: [ 105.259466] usb 2-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
Jul 4 08:54:47 Fabio-VGN4290S kernel: [ 105.259471] usb 2-1: Product: DataTraveler 3.0
Jul 4 08:54:47 Fabio-VGN4290S kernel: [ 105.259475] usb 2-1: Manufacturer: Kingston
Jul 4 08:54:47 Fabio-VGN4290S kernel: [ 105.259479] usb 2-1: SerialNumber: 5404B1090100E6
Jul 4 08:54:47 Fabio-VGN4290S kernel: [ 105.268581] usb-storage 2-1:1.0: USB Mass Storage device detected
Jul 4 08:54:47 Fabio-VGN4290S kernel: [ 105.270004] scsi host3: usb-storage 2-1:1.0
Jul 4 08:54:47 Fabio-VGN4290S mtp-probe: checking bus 2, device 3: "/sys/devices/pci0000:00/0000:00:14.0/usb2/2-1"
Jul 4 08:54:47 Fabio-VGN4290S mtp-probe: bus: 2, device: 3 was not an MTP device
Jul 4 08:54:48 Fabio-VGN4290S kernel: [ 106.269892] scsi 3:0:0:0: Direct-Access Kingston DataTraveler 3.0 PQ: 0 ANSI: 6
Jul 4 08:54:48 Fabio-VGN4290S kernel: [ 106.272812] sd 3:0:0:0: Attached scsi generic sg2 type 0
Jul 4 08:54:48 Fabio-VGN4290S kernel: [ 106.273562] sd 3:0:0:0: [sdb] 30218842 512-byte logical blocks: (15.5 GB/14.4 GiB)
Jul 4 08:54:48 Fabio-VGN4290S kernel: [ 106.273798] sd 3:0:0:0: [sdb] Write Protect is off
Jul 4 08:54:48 Fabio-VGN4290S kernel: [ 106.273805] sd 3:0:0:0: [sdb] Mode Sense: 4f 00 00 00
Jul 4 08:54:48 Fabio-VGN4290S kernel: [ 106.274038] sd 3:0:0:0: [sdb] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
Jul 4 08:54:48 Fabio-VGN4290S kernel: [ 106.280906] sdb: sdb1
Jul 4 08:54:48 Fabio-VGN4290S kernel: [ 106.282575] sd 3:0:0:0: [sdb] Attached SCSI removable disk
Jul 4 08:54:52 Fabio-VGN4290S udisksd[1775]: Ignoring SCSI command SYNCHRONIZE CACHE failure (Non-GOOD SCSI status from SGIO v3 ioctl: status=2 host_status=0 driver_status=8) on /dev/sdb
Jul 4 08:54:52 Fabio-VGN4290S udisksd[1775]: Successfully sent SCSI command START STOP UNIT to /dev/sdb
Jul 4 08:54:52 Fabio-VGN4290S udisksd[1775]: Powered off /dev/sdb - successfully wrote to sysfs path /sys/devices/pci0000:00/0000:00:14.0/usb2/2-1/remove
Jul 4 08:54:52 Fabio-VGN4290S kernel: [ 110.265737] usb 2-1: USB disconnect, device number 3
Jul 4 08:54:53 Fabio-VGN4290S kernel: [ 111.033021] usb 2-1: new SuperSpeed USB device number 4 using xhci_hcd
Jul 4 08:54:53 Fabio-VGN4290S kernel: [ 111.060888] usb 2-1: New USB device found, idVendor=0951, idProduct=1666
Jul 4 08:54:53 Fabio-VGN4290S kernel: [ 111.060897] usb 2-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
Jul 4 08:54:53 Fabio-VGN4290S kernel: [ 111.060902] usb 2-1: Product: DataTraveler 3.0
Jul 4 08:54:53 Fabio-VGN4290S kernel: [ 111.060906] usb 2-1: Manufacturer: Kingston
Jul 4 08:54:53 Fabio-VGN4290S kernel: [ 111.060910] usb 2-1: SerialNumber: 5404B1090100E6
Jul 4 08:54:53 Fabio-VGN4290S kernel: [ 111.070342] usb-storage 2-1:1.0: USB Mass Storage device detected
Jul 4 08:54:53 Fabio-VGN4290S kernel: [ 111.070657] scsi host4: usb-storage 2-1:1.0
Jul 4 08:54:53 Fabio-VGN4290S mtp-probe: checking bus 2, device 4: "/sys/devices/pci0000:00/0000:00:14.0/usb2/2-1"
Jul 4 08:54:53 Fabio-VGN4290S mtp-probe: bus: 2, device: 4 was not an MTP device
Jul 4 08:54:54 Fabio-VGN4290S kernel: [ 112.071926] scsi 4:0:0:0: Direct-Access Kingston DataTraveler 3.0 PQ: 0 ANSI: 6
Jul 4 08:54:54 Fabio-VGN4290S kernel: [ 112.073510] sd 4:0:0:0: Attached scsi generic sg2 type 0
Jul 4 08:54:54 Fabio-VGN4290S kernel: [ 112.077484] sd 4:0:0:0: [sdb] 30218842 512-byte logical blocks: (15.5 GB/14.4 GiB)
Jul 4 08:54:54 Fabio-VGN4290S kernel: [ 112.077699] sd 4:0:0:0: [sdb] Write Protect is off
Jul 4 08:54:54 Fabio-VGN4290S kernel: [ 112.077708] sd 4:0:0:0: [sdb] Mode Sense: 4f 00 00 00
Jul 4 08:54:54 Fabio-VGN4290S kernel: [ 112.078011] sd 4:0:0:0: [sdb] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
Jul 4 08:54:54 Fabio-VGN4290S kernel: [ 112.085312] sdb: sdb1
Jul 4 08:54:54 Fabio-VGN4290S kernel: [ 112.089278] sd 4:0:0:0: [sdb] Attached SCSI removable disk
Jul 4 08:55:00 Fabio-VGN4290S udisksd[1775]: Mounted /dev/sdb1 at /media/fabio/ USB on behalf of uid 1000

Per me é arabo ma noto diversi errori... Non saprei... In pratica ho messo e tolto la Pennetta per 2 volte. E questo é il registro...

[andrea111]

Non emerge nulla, semplicemente allo smontaggio segue l'immediato rimontaggio senza alcuna indicazione sul perché.

Vediamo qualcosa sul PC, posta in successione

Codice Seleziona Espandi

lspci
lsb_release -a
uname -a

Inoltre fai anche questa prova: avvia una live e da lì vedi se ti dà lo stesso problema oppure è OK.

Al momento parrebbe un bug che si presenta con alcuni componenti hardware.

[fabio.o]

Ciao
Ho risolto formattando chiavetta e hdd in fat32 ... Ora pare che funzionano ...
Comunque quei registri vecchi si possono eliminare? Vedo che occupano anche 50 MB l uno e ce ne sono tantissimi vecchi e addirittura alcuni compressi ... Secondo te quelli vecchi si possono eliminare?

[andrea111]

Ottimo che hai risolto.
Quindi era una questione di file system, ma cosa era prima? ext4 o ntfs.

Sì i file di registro vecchi li puoi eliminare tranquillamente, sopratutto se in formato compresso perché sono i più vecchi.
Bada comunque a non cancellarli tutti, almeno uno lo devi lasciare, quello più recente e attuale: è un file di sistema e se cancelli anche quello il sistema potrebbe rifiutarsi di partire.

Metti il [Risolto] al titolo del primo post, quello con cui hai aperto la discussione.

[fabio.o]

Era ext4...
Comunque grazie del supporto e degli insegnamenti Andrea111